#
# Utah Scientific MXLATOR Configuration Data
#
#


[CONFIG_DEFINITION_DATA_START]

[FLASH_VERSION_DATA_START]
# the following fields are REQUIRED
#  the format for this section is a FIELD LABEL followed by FIELD DATA
#  the FIELD LABEL must have a ':' as the last character
#  the FIELD DATA  must start with a '@' char and be no longer than 20 characters
#
#  FILE_FORMAT:   @00.01
#  CUSTOMER_NAME: @xxxxxxxxxxxxxxxxxxxx
#  SYSTEM_NAME:   @xxxxxxxxxxxxxxxxxxxx
#  FILE_DATE:     @MM/DD/YYYY
#  FILE_REVISION: @??

FILE_FORMAT_MX:	 @01.01
CUSTOMER_NAME:  @USI-DEFAULT
SYSTEM_NAME:    @USI-DEFAULT
FILE_DATE:      @01/21/2005
FILE_REVISION:  @01


[MX_BUS_DATA_START]
# the following fields are REQUIRED
#  the format for this section is a FIELD LABEL followed by FIELD DATA
#  the FIELD LABEL must have a ':' as the last character
#  the FIELD DATA  must start with a '@' char and be no longer than 20 characters
#
# The purpose of this section is to provide readback information to the SC-4 controller for
# ALL non-MX routers on the system.  Therefore, keep the output numbers in blocks of 16
# MX level number cannot be duplicated (within each section)
#
#  ENABLED:           @TRUE or FALSE
#  READ_BACK_STATUS:  @0 or 1 or STATUS
#  READ_BACK:         @<read back value in hex 0x... >
#  DISCONNECT_INPUT:  @<input designated as disconnect>
#  LEVEL_MAPPING:     @<mx level number>,<output start number>,<output length number>

ENABLED:                @TRUE
READ_BACK_STATUS:       @1
READ_BACK:              @0x60
DISCONNECT_INPUT:       @4095
LEVEL_MAPPING:          @4, 0, 160
LEVEL_MAPPING:          @5, 0, 160
LEVEL_MAPPING:          @6, 0, 160
LEVEL_MAPPING:          @7, 0, 160


[SC_BUS_DATA_START]
# the following fields are REQUIRED
#  the format for this section is a FIELD LABEL followed by FIELD DATA
#  the FIELD LABEL must have a ':' as the last character
#  the FIELD DATA  must start with a '@' char and be no longer than 20 characters
#
# Input and Output offsets are simply added to the incoming I/O values from the MX bus.
# MX level number cannot be duplicated (within each section)
#
#  ENABLED:              @TRUE or FALSE
#  DISCONNECT_INPUT:     @nnnn
#  MX_SC_MAPPING:        @<MX level>,<SC level>,<MX output start>,<MX output length>,<SC output offset>,<SC input offset>
#  REFRESH_LEVEL:        @<level (0 thru 7)>
#  REFRESH_DECADE:       @<decade (0 thru 31)>
#  MX_SCDR_MAPPING:      @<MX level>,<SC level>,<MX output start>,<MX output length>,<SC output offset>,<SC input offset>,<SC disconnect>
#  SCDR_AUTO_DISCONNECT: @TRUE or FALSE
#  SCDR_EXCLUSIVE_LOCK:  @TRUE or FALSE

ENABLED:                @TRUE
MX_SC_MAPPING:          @4, 0, 0, 160, 0, 0
MX_SC_MAPPING:          @5, 1, 0, 160, 0, 0
SCDR_AUTO_DISCONNECT:	@TRUE
SCDR_EXCLUSIVE_LOCK:	@FALSE
REFRESH_LEVEL:		@0
REFRESH_LEVEL:		@1
REFRESH_DECADE:		@0
REFRESH_DECADE:		@1
REFRESH_DECADE:		@2
REFRESH_DECADE:		@3
REFRESH_DECADE:		@4
REFRESH_DECADE:		@5
REFRESH_DECADE:		@6
REFRESH_DECADE:		@7
REFRESH_DECADE:		@8
REFRESH_DECADE:		@9
REFRESH_DECADE:		@10
REFRESH_DECADE:		@11
REFRESH_DECADE:		@12
REFRESH_DECADE:		@13
REFRESH_DECADE:		@14
REFRESH_DECADE:		@15

[DB_BUS_DATA_START]
# the following fields are REQUIRED
#  the format for this section is a FIELD LABEL followed by FIELD DATA
#  the FIELD LABEL must have a ':' as the last character
#  the FIELD DATA  must start with a '@' char and be no longer than 20 characters
#
# Input and Output offsets are simply added to the incoming I/O values from the MX bus.
# MX level number cannot be duplicated (within each section)
#
#  ENABLED:           @TRUE or FALSE
#  320_OUTPUTS:       @TRUE or FALSE   *TRUE = 7 levels 320 outputs / FALSE = 8 levels 160 outputs
#  DISCONNECT_INPUT:  @nnnn
#  MX_DB_MAPPING:     @<MX level>,<DB level>,<MX output start>,<MX output length>,<DB output offset>,<DB input offset>
#  REFRESH_LEVEL:     @<level (0 thru 7)>
#  REFRESH_DECADE:    @<decade (0 thru 31)>

ENABLED:                @TRUE
320_OUTPUTS:            @TRUE
MX_DB_MAPPING:		@6, 0, 0, 160, 0, 0
MX_DB_MAPPING:		@7, 1, 0, 160, 0, 0
REFRESH_LEVEL:		@0
REFRESH_LEVEL:		@1
REFRESH_DECADE:		@0
REFRESH_DECADE:		@1
REFRESH_DECADE:		@2
REFRESH_DECADE:		@3
REFRESH_DECADE:		@4
REFRESH_DECADE:		@5
REFRESH_DECADE:		@6
REFRESH_DECADE:		@7
REFRESH_DECADE:		@8
REFRESH_DECADE:		@9
REFRESH_DECADE:		@10
REFRESH_DECADE:		@11
REFRESH_DECADE:		@12
REFRESH_DECADE:		@13
REFRESH_DECADE:		@14
REFRESH_DECADE:		@15


[ESBC_BUS_DATA_START]
#NOTE! Up to 6 es-bus control routers can be defined (limited by serial ports). Simply duplicate the ESBC_BUS_DATA_START section again.
# the following fields are REQUIRED
#  the format for this section is a FIELD LABEL followed by FIELD DATA
#  the FIELD LABEL must have a ':' as the last character
#  the FIELD DATA  must start with a '@' char and be no longer than 20 characters
#
# Most ES-BUS cases require both serial port types and mapping types to be configured, along with the RCP3_BUS_DATA_START
# SERIAL_PORT is logical and SERIAL_PORT_TR is physical (used for pathfinding)
# The MX_ESBC_LCL_MAPPING applies to the SERIAL_PORT_TR
#
#  ENABLED:			@TRUE or FALSE
#  SERIAL_PORT:		@<port(1 thru 6)>,<baud rate>,<bit lengh>,<stop bits>,<parity>   *parity can only be (O)dd, (E)ven, or (N)one   (Odd is default)
#  SERIAL_PORT_TR:	@<port(1 thru 6)>,<baud rate>,<bit lengh>,<stop bits>,<parity>   *parity can only be (O)dd, (E)ven, or (N)one   (Odd is default)
#  MX_ESBC_MAPPING:	@<MX level>,<ESBC level>,<MX output start>,<MX output length>,<ESBC output offset>,<ESBC input offset>,<ESBC non-confirm mx source>
#  MX_ESBC_LCL_MAPPING:	@<MX level>,<ESBC level>,<MX output start>,<MX output length>,<ESBC output offset>,<ESBC input offset>,<ESBC non-confirm mx source>

ENABLED:                @FALSE
SERIAL_PORT:            @2, 38400, 8, 1, O
SERIAL_PORT_TR:         @3, 38400, 8, 1, O
MX_ESBC_MAPPING:        @3, 1, 0, 100, 0, 0
MX_ESBC_MAPPING:        @4, 2, 200, 10, -5, 57
MX_ESBC_LCL_MAPPING:    @5, 1, 0, 144, 0, 0

[ESBC_BUS_DATA_START]
#NOTE! Up to 6 es-bus control routers can be defined (limited by serial ports). Simply duplicate the ESBC_BUS_DATA_START section again.
# the following fields are REQUIRED
#  the format for this section is a FIELD LABEL followed by FIELD DATA
#  the FIELD LABEL must have a ':' as the last character
#  the FIELD DATA  must start with a '@' char and be no longer than 20 characters
#
# Most ES-BUS cases require both serial port types and mapping types to be configured, along with the RCP3_BUS_DATA_START
# SERIAL_PORT is logical and SERIAL_PORT_TR is physical (used for pathfinding)
# The MX_ESBC_LCL_MAPPING applies to the SERIAL_PORT_TR
#
#  ENABLED:			@TRUE or FALSE
#  SERIAL_PORT:         @<port(1 thru 6)>,<baud rate>,<bit lengh>,<stop bits>,<parity>   *parity can only be (O)dd, (E)ven, or (N)one   (Odd is default)
#  SERIAL_PORT_TR:	@<port(1 thru 6)>,<baud rate>,<bit lengh>,<stop bits>,<parity>   *parity can only be (O)dd, (E)ven, or (N)one   (Odd is default)
#  MX_ESBC_MAPPING:     @<MX level>,<ESBC level>,<MX output start>,<MX output length>,<ESBC output offset>,<ESBC input offset>,<ESBC non-confirm mx source>
#  MX_ESBC_LCL_MAPPING: @<MX level>,<ESBC level>,<MX output start>,<MX output length>,<ESBC output offset>,<ESBC input offset>,<ESBC non-confirm mx source>

ENABLED:                @FALSE
SERIAL_PORT:            @1, 38400, 8, 1, O
SERIAL_PORT_TR:         @6, 38400, 8, 1, O
MX_ESBC_LCL_MAPPING:    @3, 1, 0, 144, 0, 0


[ESTRC_BUS_DATA_START]
#
# This section is not really used and can be ignored.
#
#NOTE! Up to 6 estrc bus control routers can be defined (limited by serial ports). Simply duplicate the ESTRC_BUS_DATA_START section again.
# the following fields are REQUIRED
#  the format for this section is a FIELD LABEL followed by FIELD DATA
#  the FIELD LABEL must have a ':' as the last character
#  the FIELD DATA  must start with a '@' char and be no longer than 20 characters
#
#  ENABLED:             @TRUE or FALSE
#  SERIAL_PORT:         @<port(1 thru 6)>,<baud rate>,<bit lengh>,<stop bits>,<parity>   *parity can only be (O)dd, (E)ven, or (N)one   (Odd is default)

ENABLED:			@FALSE
SERIAL_PORT:		@6, 38400, 8, 1, O


[ESTRC_BUS_DATA_START]
#
# This section is not really used and can be ignored.
#
#NOTE! Up to 6 estrc bus control routers can be defined (limited by serial ports). Simply duplicate the ESTRC_BUS_DATA_START section again.
# the following fields are REQUIRED
#  the format for this section is a FIELD LABEL followed by FIELD DATA
#  the FIELD LABEL must have a ':' as the last character
#  the FIELD DATA  must start with a '@' char and be no longer than 20 characters
#
#  ENABLED:             @TRUE or FALSE
#  SERIAL_PORT:         @<port(1 thru 6)>,<baud rate>,<bit lengh>,<stop bits>,<parity>   *parity can only be (O)dd, (E)ven, or (N)one   (Odd is default)

ENABLED:			@FALSE


[RCP3_BUS_DATA_START]
# the following fields are REQUIRED
#  the format for this section is a FIELD LABEL followed by FIELD DATA
#  the FIELD LABEL must have a ':' as the last character
#  the FIELD DATA  must start with a '@' char and be no longer than 20 characters
#
#  ENABLED:           @TRUE or FALSE
#  DISCONNECT_INPUT:  @nnnn
#  IP:                @<ip "XXX.XXX.XXX.XXX">  (of the SC-4 controller)

ENABLED:			@FALSE
IP:				@192.168.005.100



[PROSAN_BUS_DATA_START]
#NOTE! Up to 6 Prosan bus control routers can be defined (limited by serial ports). Simply duplicate the PROSAN_BUS_DATA_START section again.
# the following fields are REQUIRED
#  the format for this section is a FIELD LABEL followed by FIELD DATA
#  the FIELD LABEL must have a ':' as the last character
#  the FIELD DATA  must start with a '@' char and be no longer than 20 characters
#
#  ENABLED:           @TRUE or FALSE
#  SERIAL_PORT:       @<port(1 thru 6)>,<baud rate>,<bit lengh>,<stop bits>,<parity>   *parity can only be (O)dd, (E)ven, or (N)one   (Odd is default)
#  NUMBER_FORMAT:     @<2 or 3>   *number of input or output digits supported in protocol
#  MX_PROSAN_MAPPING: @<MX level>,<PROSAN level>,<MX output start>,<MX output length>,<PROSAN output offset>,<PROSAN input offset>
#
#NOTE! The prosan router has levels 'A' thru 'H'.
#      The prosan router input/output 1 is the first bus (MX uses 0 as the first bus).
#      The input/output offset must map the 0 and 1 relative offset. The offset will almost always be odd.
#      The following will map the first input, output and level of Prosan to the first input, output and level of MX.
#      MX_PROSAN_MAPPING:   0,A,0,64,1,1
#

ENABLED:			@FALSE
SERIAL_PORT:		@1, 9600, 8, 1, O
NUMBER_FORMAT:		@2
#MX_PROSAN_MAPPING:	@0, E, 128, 64, -127, 65
#MX_PROSAN_MAPPING:	@1, F, 64, 128, 65, 1
MX_PROSAN_MAPPING:	@3, G, 0, 64, 1, 1
#MX_PROSAN_MAPPING:	@4, H, 0, 128, 1, 1


[PROSAN_BUS_DATA_START]
#NOTE! Up to 6 Prosan bus control routers can be defined (limited by serial ports). Simply duplicate the PROSAN_BUS_DATA_START section again.
# the following fields are REQUIRED
#  the format for this section is a FIELD LABEL followed by FIELD DATA
#  the FIELD LABEL must have a ':' as the last character
#  the FIELD DATA  must start with a '@' char and be no longer than 20 characters
#
#  ENABLED:           @TRUE or FALSE
#  SERIAL_PORT:       @<port(1 thru 6)>,<baud rate>,<bit lengh>,<stop bits>,<parity>   *parity can only be (O)dd, (E)ven, or (N)one   (Odd is default)
#  NUMBER_FORMAT:     @<2 or 3>   *number of input or output digits supported in protocol
#  MX_PROSAN_MAPPING: @<MX level>,<PROSAN level>,<MX output start>,<MX output length>,<PROSAN output offset>,<PROSAN input offset>
#
#NOTE! The prosan router has levels 'A' thru 'H'.
#      The prosan router input/output 1 is the first bus (MX uses 0 as the first bus).
#      The input/output offset must map the 0 and 1 relative offset. The offset will almost always be odd.
#      The following will map the first input, output and level of Prosan to the first input, output and level of MX.
#      MX_PROSAN_MAPPING:   0,A,0,64,1,1
#

ENABLED:			@FALSE
SERIAL_PORT:		@1, 19200, 8, 1, O
NUMBER_FORMAT:		@2


[LOGFILE_TARGET_DEFINITIONS_START]
# This section defines the NFS address & directory the system
# will use as remote file systems
# Currently the log xfer function in the only target defined.
#EXAMPLE:
#192.168.004.010,/c/rt/usilogs/kyw-hd                    ,YES/NO
#
#      IP           NFS LOGGING DIRECTORY (40 CHARS)     Action
#    ADDRESS                                             Enabled
#--------------,----------------------------------------,--------
192.168.005.200,/c/usi/usi-mxl01                        ,NO



[END_CONFIG_FILE]