############################################################################### # # SC4 VERSION 2 LOG FILE # ############################################################################### ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 06-22-2017 # Why: Release sc4 s/w # ############################################################################### [VERSION:] SC4_2-08#1_06/22/2017_19-12-24 [FEATURES] 1. Chng Changes in how panel lost processing is done related to ucon. Some panels @ RAI would be lost in ucon but show as present in SC4 utilities. The merge with the CVS code brought over these changes [BUG FIXES] [NOTES] =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 04-30-2016 # Why: Release sc4 s/w maint release # ############################################################################### [VERSION:] SC4_2-07-02#1_04/30/2016_18-09-39 [FEATURES] 1. Added custom physical source AXON_AUDIO_EMBEDDER_OFF_SRC (4094) to allow cerebrum panels to status audio outputs when they switch the embedders off. To use ucon must be encoded with a logical source with audio levels set to a value of 4094. [BUG FIXES] [NOTES] =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 02-08-2016 # Why: Release sc4 s/w # ############################################################################### [VER_SION:] SC4_2-07_Beta-04#67_02/08/2016_11-20-15 [FEATURES] 1. Added ability to drive TTL Error output pins on Alarm Connector located on the rear of the chassis. PIN 1 PRIMARY BOARD RUNNING , normally HI if board plugged into chassis and software is running normally. PIN 2 GENERAL ERROR, Mimicks behaviour of SMPTE Alarm on SC4 PIN 3 PARTNER BOARD NOT INSTALLED, Normally Low, Goes Hi if primary board detects the partner card is not installed PIN 4 PARTNER BOARD MALFUNCTION, Normally Low, goes HI if primary board detects the partner card is not communicating or malfunctioning in some manner. 2. Added ability to control TDM Audio matrix upto 4032 squared. Required BUG FIX in verison #67 to fix report errors in Rman/SC4. [BUG FIXES] [NOTES] =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 08-03-2014 # Why: Release sc4 s/w # ############################################################################### [VER_SION:] SC4_2-07_Beta-03#1_08/03/2014_14-19-12 [FEATURES] [BUG FIXES] [NOTES] 1. Changes from CVS branch for tielines, timecode access, others???? =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 03-29-2014 # Why: Release sc4 s/w # ############################################################################### [VER_SION:] SC4_2-07_Beta-01#1_03/29/2014_12-16-45 [FEATURES] 1. Support > 16 levels using Linked Devices (Source & Destination) Linked Devices support > 16 levels by creating a link between 2 devices. 1 being a Primary a 2nd being a Secondary. This is done for both sources and destinations. If the user takes a PRIMARY Source to a PRIMARY Destination the SC4 will automatically do the take for both SECONDARY devices. 2. Support LC32 control panels on Ethernet. This implements RCP3 control & Programming for UCP-LC32 control panels. NOTE that UCON version 4.3-rc2 is required at a minimum [BUG FIXES] [NOTES] =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 03-29-2014 # Why: Release sc4 s/w # ############################################################################### [VER_SION:] SC4_2-06-02_rc5#1_03/29/2014_10-09-43 [FEATURES] 1. Enh SC4 now monitors timecode input and will update system clock and front panel display if a difference of > 5 seconds is detected. Also forces updates at 02:02:00 each day [BUG FIXES] [NOTES] =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 03-08-2014 # Why: Release sc4 s/w # ############################################################################### [VER_SION:] SC4_2-06-02_rc4#1_03/26/2014_06-40-33 [BUG FIXES] 1. New fast ACK commands below had a bug where they sent the wrong interface. Fixed. [FEATURES] 1. Enh Max device count for System increased to 3072 Src & Dest. UCP Panels are still limited to 2450 total devices. Only exception are UCP-LC32 and softpanels 03-07-2014 RWT 2. Change ACK of Take Commands on RCP3 are now done on the "fast" side of the Queues to help with the RAI system and lots of takes from a RCP3 device 03-18-2014 RWT 2.6.2-rc2 had a bug with this. Fixed in 2.6.2-rc3 3. Exp Serial Port error tracking/reporting enhancements to help track down issue @ OETA. activated by serdump 4. Change serdump application included in romfs image for SC4 & SC400_E distros [NOTES] This verison also includes the following: [VER_SION:] SC4_2-06-02_rc2#1_03/16/2014_13-18-06 [VER_SION:] SC4_2-06-01_rc6#12_01/14/2014_15-00-59 =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 03-08-2014 # Why: Release sc4 s/w # ############################################################################### [VER_SION:] SC4_2-06-02_rc1#1_03/11/2014_09-42-04 [FEATURES] 1. Enh Max device count for System increased to 3072 Src & Dest. UCP Panels are still limited to 2450 total devices. Only exception are UCP-LC32 and softpanels 03-07-2014 RWT [VER_SION:] SC4_2-06-01_rc6#12_01/14/2014_15-00-59 [FEATURES] 1. Exp Serial Port error tracking/reporting enhancements to help track down issue @ OETA. activated by serdump 2. Change serdump application included in romfs image [BUG FIXES] [NOTES] =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 11-19-2013 # Why: Release sc4 s/w # ############################################################################### [VER_SION:] SC4_2-06-01_rc4#4_11/12/2013_13-54-12 [FEATURES] 1. Enh Max device count for UCP panels was increased from 1800 to 2450 to match V3.0 UCP software release. [BUG FIXES] [BUG FIXES] [NOTES] =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 10-30-2013 # Why: Release sc4 s/w # ############################################################################### [VER_SION:] SC4_2-06-01_rc3#1_10/30/2013_13-59-24 [FEATURES] 1. Change Misc Change made to reprogramming process for UCP-LC32 control panels in that Ucon no longer delays while the panel flash is programmed. [BUG FIXES] 2. Bug ucp config operations could hang. This was fixed. See configClient.c:readConfigClientUNetReprog() for details. [BUG FIXES] [NOTES] =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 10-14-2013 # Why: Release sc4 s/w # ############################################################################### [VER_SION:] SC4_2-06-01_rc2#2_10/18/2013_10-16-04 [FEATURES] 1. ENH Datarouter processing changed to allow a FIXED CONTROLLER device to be a Source switched up to a AUTO DEST device as the Destination and the destination be treated as a TRIB rather than the normal case where it would be a CONTROLLER. 2. ENH Added ability to provide 32 levels of control by linking 2 logical devices together. If the controller detects a PRIMARY SRC swtiched to a PRIMARY destination, the controller automatically does a 2nd take with the 2 secondary devices. 3. ENH Changed the way control panel NODE ID's are sent over to UCON. We now allow for > 255 devices. NOTE!!! This SC4 version REQUIRES UCON-V4 version 4.3 and higher to work properly [BUG FIXES] [NOTES] =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC4 Router Controller # When: 06-20-2013 # Why: Release sc4 s/w # ############################################################################### [VER_SION:] SC4_2-06_rc2#1_06/20/2013_06-24-43 [FEATURES] [BUG FIXES] 1. Monitor matrix takes would sometimes crash the SC4. required follow levels active in SC4 and then a take on an output with some levels undefined. The undefined levels output value is -1 and the monitor matrix handler was not checking for something less than 0 [NOTES] =============================================================================== ############################################################################### # # Who: Roger Thornblad # What: SC400 (expanded) Router Controller # When: 06-12-2013 # Why: Release sc400 Expanded Router Controller s/w # ############################################################################### [VER_SION:] SC4_2-06_rc1#1_06/12/2013_16-24-41 [FEATURES] 1. Added support for new Utah UDS Routers (UDS-32/UDS-64/UDS-144) UDS-32 = 0x5a UDS-64 = 0x5B UDS-144 = 0x5C 2. Added support for numeric switching up to 2000 devices in SC4 devices. This is in the router domain not the MX domain 3. Added support for new Utah 400 TIMECODE Router UT400_TIMECODE = 0x56, 4. Implements Audio shuffling support for UCP and RCP panels. 5. Implements config operations of UCP-LC32 panels over unet using gzip/unzip process [BUG FIXES] 1. Outputs that have an active shuffle would not refresh if the router chassis was power cycled. Fixed in mxHandler.c:doRefresh() where a non straight thru or single source setup would reset a index into the 2. Fix crash in shuffle system when a output was not defined with a valid bnc number [NOTES] =============================================================================== ############################################################################### # # SC4 VERSION 2 LOG FILE END # ###############################################################################